How To Extend Toilet Water Supply Line

Delight annals to participate in our discussions with 2 million other members - it's free and quick! Some forums tin can simply be seen by registered members. After yous create your account, you'll exist able to customize options and admission all our xv,000 new posts/day with fewer ads.

01-01-2017, 03:38 PM

2,766 posts, read half-dozen,928,576 times Reputation: 1480

Hoping someone can assist me out hither, so I needed to install a new toilet in my mobile home. Toilet is installed and ready to go, but low and behold the water supply line is to curt. Some other result is I believe the piping you see is polybutylene, so how tin can I somehow extend this to achieve the toilet? Is there some sort of extension that would work where I tin easily connect, or would I be able to supersede most of the line with a steel braided one using something similar a sharkbite? And yes I know polybutylene is no good, just I can't afford to replace it throughout the unabridged dwelling house, then I'm stuck having to work around information technology.

01-01-2017, 03:44 PM

MrRational Location: The Triad (NC) 32,581 posts, read 76,017,641 times Reputation: 40378

Quote: Originally Posted by LoneStarJerry the water supply line is too short. Buy 1 that is long enough or EXTEND the one you have. Any decent hardware shop nigh a trailer park will have what you demand.

01-01-2017, 04:xvi PM

AksarbeN Location: Looking over your shoulder 31,304 posts, read 31,107,869 times Reputation: 84438

Looks like the riser with the shutoff coming from the floor is only a few inches shorter than the connectedness to the toilet tank and appears to be commencement to the left of the connection. If that'southward right and the toilet is mounted to the drain, then you lot'll need a "flexible" extension the yous can connect to both the water supply and the tank and it will have to be "long enough" to make a graceful bend to lineup with the toilet. The extension might take to be long enough to brand a complete 360 loop to attach to the toilet tank. I don't recollect y'all can exercise a couple of –South- curves in the flex that would work hither. one/2 in. Comp x 7/8 in. Ballcock x 9 in. Braided Polymer Toilet Connector-B3-9DL F - The Dwelling Depot Be sure to get a flexible connector with the " correct" ends or fittings there are several unlike types of extensions.

01-01-2017, 04:44 PM

ii,766 posts, read six,928,576 times Reputation: 1480

Quote: Originally Posted by AksarbeN Looks like the riser with the shutoff coming from the flooring is merely a few inches shorter than the connection to the toilet tank and appears to exist start to the left of the connexion. If that's correct and the toilet is mounted to the drain, and so y'all'll demand a "flexible" extension the you tin can connect to both the water supply and the tank and it volition have to exist "long enough" to make a graceful bend to lineup with the toilet. The extension might have to be long enough to make a complete 360 loop to attach to the toilet tank. I don't recollect you lot tin do a couple of –S- curves in the flex that would work here. 1/2 in. Comp x vii/8 in. Ballcock 10 ix in. Braided Polymer Toilet Connector-B3-9DL F - The Home Depot Be sure to become a flexible connector with the " right" ends or fittings in that location are several different types of extensions. Thanks, I appreciate the help. That'southward what I'chiliad wondering is considering the line in the link you lot shared with me will connect to the toilet merely fine, but won't connect to the electric current water line. So would they make a connector with an end that would connect to my current supply line? Also my photo is a fleck deceiving for some reason, the lead line actually lines up to the toilet tank hookup rather well, only have to move it over a tad, but it's still short of course.

01-01-2017, 05:58 PM

AksarbeN Location: Looking over your shoulder 31,304 posts, read 31,107,869 times Reputation: 84438

Quote: Originally Posted by LoneStarJerry Thanks, I appreciate the help. That's what I'm wondering is because the line in the link you shared with me volition connect to the toilet just fine, but won't connect to the current water line. So would they brand a connector with an cease that would connect to my current supply line? Also my photo is a bit deceiving for some reason, the pb line actually lines up to the toilet tank hookup rather well, just accept to movement it over a tad, but information technology's withal short of course. Yous might accept to cutting off the end of the riser pipage and connect a different just "standard" fitting to it then that the flexible extension will attach. Fundamental word here is "standard fitting". Check with the guy working at HomeDepot in the plumbing department or in Ace Hardware. I've had meliorate luck with my local Ace store in the neighborhood.

01-01-2017, 08:53 PM

Location: Johns Creek, GA 16,181 posts, read 60,069,037 times Reputation: 20727

You'll demand to replace the shutoff valve with a similar valve that has 3/8 male so yous can apply a standard riser tube or supply line. Something like this- https://www.plumbingsupply.com/image...p-valve-lg.jpg

01-04-2017, 03:05 PM

duster1979 Location: Keosauqua, Iowa ix,483 posts, read nineteen,566,939 times Reputation: 13199

Assuming your Quest line is 1/2", Shark Seize with teeth makes a shutoff valve that's 1/2" Shark Bite on one terminate and 3/8 compression on the other: SharkBite 1/ii in. Chrome-Plated Contumely Push-to-Connect x three/viii in. O.D. Compression Quarter-Turn Straight Stop Valve-23037-0000LF - The Dwelling house Depot If I were in your shoes, I'd cutting your existing line just below the valve and install one of these in information technology's identify. A standard flexible three/viii pinch x vii/viii ballcock flexible supply line can then be connected between the new valve and the toilet. I've had some customers tell me that the Shark Bite fittings don't work well with Quest line, but about study no problems. My guess is that those with issues were dealing with lines that had frozen and swelled at some indicate.

01-07-2017, 03:08 PM

2,766 posts, read half-dozen,928,576 times Reputation: 1480

Quote: Originally Posted past duster1979 Assuming your Quest line is 1/2", Shark Seize with teeth makes a shutoff valve that's 1/2" Shark Bite on one end and 3/8 pinch on the other: SharkBite ane/two in. Chrome-Plated Brass Button-to-Connect 10 three/8 in. O.D. Compression Quarter-Plough Straight Stop Valve-23037-0000LF - The Home Depot If I were in your shoes, I'd cut your existing line just below the valve and install one of these in it's place. A standard flexible 3/8 compression ten 7/8 ballcock flexible supply line can and then be continued betwixt the new valve and the toilet. I've had some customers tell me that the Shark Seize with teeth fittings don't work well with Quest line, but near report no problems. My guess is that those with issues were dealing with lines that had frozen and swelled at some betoken. Thanks so much for this! I believe this pointed me in the right management, what I would practise instead is utilize the 1/ii" Polybutylene adapter coupling from SharkBite first, then catechumen to PEX pipe where I could use the exact valve you shared. Appreciate anybody's responses by the style!

Please register to post and access all features of our very popular forum. It is free and quick. Over $68,000 in prizes has already been given out to active posters on our forum. Boosted giveaways are planned.

Detailed information near all U.S. cities, counties, and zip codes on our site: City-information.com.

All times are GMT -6.

How To Extend Toilet Water Supply Line,

Source: https://www.city-data.com/forum/house/2698130-toilet-water-supply-not-reaching-new.html

Posted by: williamsstenly.blogspot.com

Share this post